• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. In contrast to aluminium and timber, they don't rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will help avoid unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it could cause a large amount of damage to your home, which can make it very dangerous and potentially fatal. It is important to make sure that your windows are in good shape.

For single pane windows it is relatively easy to replace them, and uPVC window repairs the replacement will generally fit within the old frame very easily. However when you have double glazing repair pane windows that are anchored by internal beading, it'll be more difficult to get rid of the panes that are in place and replace them with new ones. In this situation you'll need locate some plastic spacers that help the new pane to fit perfectly into the window frame.

Wearing protective eyewear and thick gloves is essential when you are planning to remove the glass yourself. It is also a good idea to lay down a dropcloth before you start working on the glass, so that any fragments of glass fall onto the cloth instead of onto the floor, where they could be trodden under and cause further damage.

It's a good idea to seal the gap after the glass has been removed. This will keep drafts and water from entering your property until a professional arrives to fix the window. This also serves as an obstacle to stop criminals from getting into your home. If the gap is large, you may be interested in an alarm door that comes with an integrated window as this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. In time, they could develop a variety of issues, including sagging. A window that is sagging can cause problems with light, draughts, and even security. It is crucial to act immediately if you notice your uPVC windows are falling down.

Repositioning the hinges could aid in fixing a window which is sliding. You'll first need to open the windows to access the frame. Then, remove both the hinges at the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Close your window to check the fit after having relocated your hinges. If you're satisfied with the size of the window, tighten the screws to keep them in place.

If you can't reposition the hinges, you may need to replace the seal. Over time, rubber seals lose their elasticity and dry out and cause them to loosen. If this happens, it's essential to replace the seal as soon as possible to ensure your uPVC windows remain watertight and safe from drafts.

UPVC handles can also become loose. This is typically caused by screws that have been removed over time, but it could be due to the mechanism of the handle wearing out. It's relatively easy to repair a loose uPVC handle. You'll first need to close the window and perform a test fitting. The joints at the corners of the sash should align with the joint on the casing. If it doesn't, you can use the screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains, it's important to take action. Water leaks from windows not only lead to the degrading of the structure of your home but also hinder your efforts to control the temperature within your home. The most common reason for leaks in uPVC windows is that the sealant around the frame is damaged or missing.

This is a relatively easy fix and should be undertaken by any skilled DIYer. Depending on the severity of the problem the caulking that was used up may require removal before a fresh layer can be put on. It is important to keep in mind that when it is about uPVC window repairs you should avoid the temptation to "over-caulk' as this will only make the area more difficult to clean and decrease the efficiency of your energy usage.

Verify that the drainage holes are free of debris in them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more extreme cases, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

If the leakage is occurring between the double-glazed window, it is more likely that the problem is related to the seal, not the frame. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and open with ease, it may be the hinges that are at the fault. They can be repaired by any DIYer who is skilled and are usually completed in just a few minutes.

Like any mechanical component, hinges can wear out over time. It's very simple to change the hinges on a window, but it's simpler if you have someone to help you to hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. This can be done by checking for the arrows on each hinge. This shows which way the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window in a certain way or due to poor installation at the factory. This can often be resolved by sending us a photograph through our website and we will be pleased to offer you advice.

It is also essential to grease the hinges regularly. Applying a light engineering lubricant on the hinges is a good method to accomplish this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to open and close more easily. It can also prevent corrosion and reduce the risk of sticking. This should be done at least every year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a few various factors. The hinges can also become disaligned as a result of wear, which can cause a gap between the frame and sash. This can be easily fixed by giving them a thorough clean, however in the event that they are beyond repair it might be necessary to get them re-aligned or replaced. The second is the interlock, which is on the hinge side of the window, may be misaligned. Again, it is possible to give them a good clean, but in some cases it might be necessary to have them replaced.

These seals can wear down or become damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glass. This will help regulate indoor temperatures, and reduce draughts.

Another method of reducing drafts effectively is to use a draught-excluder. These are usually fabric tubes filled with a filler, which can be hung over your window sill. They will help block out cold air and keep your home warm and cozy!

Your upvc windows can continue to provide excellent insulation and security to your home with a little regular maintenance and repairs. It is important to remember that all windows eventually wear out and it could be cheaper to replace them instead of fixing them. If you have any problems with your upvc window it is recommended to speak with an expert immediately.